Training Course
Instrumentation process Control
Trainer : Eng. Mahmoud Abdel Fattah Ahmed
Mob. 01148695492
E.mail mahmodcontrol@yahoo.com
محتوى الكورس :Course Outlines
- Definitions of Process Measuring and Control Instrumentation
-Instrumentation and Industrial Process.
- Process Control Loop
-Process Variables : Temperature, Level , Pressure and Flow
- Components of Process Control systems : Transmitter ,Controller and Control Valve
Industrial Temperature Measurements
-Industrial Thermocouples TC and Resistance Temperature Detectors RTDs .
- Test of TC and RTDs , Tables of TC and RTDs
-Thermocouple and RTDs Temperature Transmitter
- Temperature signal converter ( TC and RTDs )
- Calibration Procedures For Temperature Transmitter and converter
- Thermocouple and RTDs applications in industry
- Digital temperature Indicator Controllers .
- Handy Temperature Calibrator and Selecting a Dry-Well Temperature Calibrator
- Temperature switches ( Calibration , Set and Reset )
- Applications of temperature Instruments in Control Systems .
Industrial Level Measurement
- level measurement in industrial process .
- Level gauges : sight glass gauges , Float , Displacer , Magnetic and Bubbler level
gauges .
- Level Measurement by Hydrostatic Head for Open and Closed Tanks .
- Level Transmitters : Differential Pressure Transmitter , Displacer Transmitters ,
Magnetic Level Transmitter , Smart Level Transmitters
- Installation , Calibration and Configuration of Differential Level Transmitters ( Smart ,
Electronic and Pneumatic )
- Interface Measurement ( Three-Phase Gravity Separators in Oil Production )
-Ultrasonic Level Transmitter.
-Radar Level Transmitter .
- Installation , Calibration and Configuration of Ultrasonic and Radar Level Transmitters
- Voltage/Current Calibrator
.- Level switches ( Calibration , Set and Reset )
- Applications of Level Instruments in Control Systems .
Industrial Pressure measurements
- Practical Methods for Pressure Measurements .
- Calibration and Maintenance of Pressure Gauges , and Ordering Pressure Gauges
- Calibration and Configuration of Pressure Transmitters ( Smart , Electronic and
Pneumatic )
- pressure switches ( Calibration , Set and Reset )
- Applications of Pressure Instruments in Control Systems .
Industrial Flow Measurement
- Flow Measurement by using orifice plate- Differential pressure (d/p) meters
- Flow Rate Measurements by using(d/p) Transmitters and Installation
- Smart transmitters Configuration and Calibration .
- Digital Flow rate Indicator Totalizer ( Calibration and Configuration)
- Flow Rate Transmitters and Square Root Extractor Input and Output
-Variable Area Flow meters - Purge-Flow Regulators
- Magnetic Flow Meters and Transmitters – Turbine flow meters
- MULTIPHASE FLOW MEASUREMENT
- Ultrasonic transit time flow measurement
- Applications of Flow Instruments in Control Systems
Instrumentation Process Control
Digital , and Pneumatic Controllers - ( PID Control )
- Process Control Loops
(Sensors , Transmitters , Controllers , Control Valves)
- Closed and open loop control system
-Feedback and Feed forward control
- Process Control by Digital Indicator controllers .
- Control Modes :
On/OFF (Two Position Controller ) – Differential Gap Controller
- Cascade and Ratio Control and applications
- PID Control ( Proportional Integral Derivative )
- Practical PID Control Algorithm .
- Proportional Control ( P )
Proportional Band - Gain - Offset
Tuning of Proportional Controller
- Integral Control (I) Reset Action .
- MPR ( Minutes Per Repeat) , RPM (Repeats Per Minute)
- Manual reset .
- PI Proportional Plus Integral Action
- Derivative ( D ) Action , rate action .
- PID Control Responses .
- Tuning PID Controllers ( Digital controllers , DCS , PLC ) .
- Programming and Configuration of Digital Controllers .
- Reverse and Direct Control Action .
- Process and Instrument Symbols and Diagrams ( P& ID).
- Troubleshooting of Process Control Loops .
الأن بايجى سيت للتدريب الهندسي بالمنصورة دورة (Instrumentation process Control )
من أهم الكورسات للمهندسين وفنين قسم كهرباء وتحكم واتصالات وذلك:
للعمل فى المصانع والمحطات وشركات البترول والبتروكيماويات فى مصر ودول الخليج
كمهندس أجهزة Instrumentation & Control Engineer
بداية الكورس السبت 2020-2-22
للاستعلام والحجز : شركة Egycet للتدريب الهندسي
العنوان :
المنصورة - شارع الجمهورية برج الغزالى -الدور الثانى امام مستشفى الجامعة بجوار محلات أسطورة
تليفون: 01023301234-
01024443031 -
0502200254
http://www.egycet.org/request-course